The Curt Front Mount Trailer Hitch Receiver # C31069 was designed around the frame of a 2014-2019 GMC Sierra 1500 and I would be very surprised if the distance between the frame rails of your 2014 Chevy Express Van Cutaway matched those of a Sierra.
The mounting holes on the # C31069 install on 31.875 inch centers. I've attached a snip form the installation instructions which shows this.
Since there isn't a custom front mount hitch available for our van, your best option is to go with... view full answer...
Our video team has included the hole spacing measurements at the end of the video I have linked for you. The holes on the short side are spaced 4 inches apart on center and on the long side they are spaced 6-1/4 inches apart on center. The holes are elongated so they don't have a diameter but they are approximately 3/8 inches by 3/4 inches. The hardware is included though.
This is going to be the best option for what you are planning. Nothing else would be as simple or work as well. view full answer...
I have some measurements of Uni-Servo Wheel Cylinder for 10", 12" and 13" Titan Brake Assemblies - Zinc - LH Item # T0977700 for you. The plunger inside has a 1.12 inch outer diameter. The rubber parts fit over a 1.5 inch diameter. And the center hole has a 0.25 inch diameter. I included some pictures showing the measurements.
The wheel cylinder does have standard fittings 3/16" with a thread size of 3/8"-24. view full answer...
For Curt trailer hitch # C15320 the weight carrying capacities are 16,000 pounds gross trailer weight and 2,400 pounds tongue weight. When used with weight distribution the gross trailer weight capacity is 17,000 pounds and the tongue weight remains the same at 2,400 pounds. It is not uncommon for a trailer hitch to have the same tongue weight capacity for weight carrying and weight distribution.
I have included links to the installation instructions and a video showing a typical installation... view full answer...
The 1/2 inch thick backing on the VanRug mat, # VRG96, is made of closed-cell foam polypropylene that is waterproof so it will not pick up moisture. view full answer...
The Buyers Products 2" Hitch Receiver For GM Express/Savana with Cutaway Chassis # 3371801102 measures 39 inches wide center to center. Then from edge of receiver tube to rear most hole 20-3/4 inches long. I've attached a photo with measurements to assist. view full answer...
The hole centers for the Buyers Products 2" Hitch Receiver # 3371801102 are 39-1/4" from drivers side frame rail to passenger side frame rail. This receiver is confirmed to fit the 2014-2021 Chevrolet/GMC Express/Savana Cutaway Chassis.
If you are looking for a receiver for your 2001 Chevrolet Express Cutaway Chassis you will need the Buyers Products 2" Hitch Receiver # 3371801100. view full answer...
Unfortunately that 12 pin rectangular plug has nothing to do with the trailer wiring harness. To add a 7-way and 4-way connector to your 2023 Chevy Express Cargo van you're going to need to buy two separate harnesses. The reason for this is that the van's with the towing package came from the factory with the 7-way connectors like item # HM40975. The other ones have nothing and no one made a custom fit 7-way that just plugs in.
The first connector you will need is the Curt Wiring Harness... view full answer...
The distance between the center of the pinhole and the center of the ball mount of the Curt MV Weight Distribution System # C17057 is a minimum 11-1/2 and a maximum of 13 inches. This is because this part can move slightly due to the tilt range of the system.
If you need a ball to go along with the MV, you will need a hitch ball that has a 1-1/4 inch diameter shank. I went ahead and attached our product page that has all of the balls we carry that have a diameter of that measurement. view full answer...
We havea Q series Curt 5th wheel hitch on display in our store so I went to measure the width of the head support. I measured 18 inches. I then called Curt to confirm and it is indeed 18 inches. view full answer...
The bracket height (distance from mounting bracket to bottom of foot) for the Electric Jack w/ Footplate # EJ-3520-BBX is 9 inches when retracted and then 28-1/2 inches when fully extended. view full answer...
The Yakima FatCat EVO 4 Ski and Snowboard Carrier - Locking - 4 Skis or 2 Boards - Black # Y03095 has mounting holes that are inches apart. I reached out to my tech contact at Yakima and he said the Old FatCat 4 mounting holes are 12 inches on center and the newer FatCat 4 EVO will be longer at about 16 inches. Once you account for the width of the Aero Crossbar SmarT-Slot Kit 2 for Yakima FatCat Ski and Snowboard Carriers # Y03098 it will be another 1/2 inch on each side for the T-slot... view full answer...
K-Source Custom Towing Mirrors # KS62169-70G, meet the factory specs of the original mirrors on a 2008 Chevy Express Van. That length is 21 inches overall measured at the bottom along the arm to the furthest edge of the mirror. To the nearest edge of the mirror it is 12 inches. view full answer...
The air bags that come in the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers # AL88204 has a 5" - 7" standard operating distance and the difference is just dependent on how much room you have available. So max is 7" if you have room for it to expand that high.
I was able to confirm this with my contact at Air Lift. view full answer...
I had our warehouse measure the Timbren Rear Suspension Enhancement System # TGMRG35 you were looking at for your 2017 Chevrolet Express Van and the rubber portion measures 5-1/8" tall as shown in the included diagram.
You can use spacers with these springs which are the 1/2" spacer # TA25722-90F00, or 1" spacer # TA25723-90AD00 though you should not need them unless you have lifted your van. If you need the spacers you will need to find a longer Grade 8 1/2" diameter T-Bolt from a local... view full answer...
There are a few things to keep in mind for your desired setup.
First, the weight rating of the hitch on your van must be more than the combined weight of your selected carrier and two scooters. Their combined total must be within the hitch's tongue weight (TW) rating. The Flint Hill Goods Cargo Carrier # FHG69ZR weighs about 77-lbs. You can add this to the weight of your two scooters to know the total TW load that will be on the hitch.
Next check the sticker on your hitch to confirm its... view full answer...
The 7" when this rack is in the folded up position, you mentioned in your question, does take the cradles of this bike rack into account. This measurement is from the center of the hitch pin hole to the closest edge of the RockyMounts BackStage Bike Rack for 2 Bikes - 2" Hitches - Wheel Mount, part # RKY10002. There is not a part of the BackStage closer than 7" to the rear of your vehicle.
If your spare tire is more than 7" from the center of your hitch pin hole, I recommend adding the... view full answer...
I went out to the warehouse with a caliper and found the diameter of the cord for the Mighty Cord RV Power Cord # A10-3025ED90 to be 0.6350". view full answer...
I went out to the warehouse and measured the Curt Trailer Hitch Receiver # 13053 to find the distance between those 2 points is 35-7/8" as you can see in the attached photo.
Please note that this trailer hitch fits the following vehicles:
2004 - 2006 Ford Van E-150
2004 - 2006 Ford Van E-250
2004 - 2006 Ford Van E-350
1975 - 1994 Ford Van Full Size
1995 - 2003 Ford Van Full Size, including Superwagon view full answer...